Daily Access Fee
- $30 per day, maximum $ 300/month
Access (key card), gowning (gloves, wipes, frocks, shoe covers, caps), all analytical equipment not listed below, and basic laboratory chemicals and reagents (solvents, cleaning chemicals, wet etching chemicals, acids including hydrofluoric acid, DI water), available labware and dishwashing, waste containers and disposal.
The entrance fee is waived when access involves only SEM imaging. In addition there is no entrance fee when entering the nanofab to retrieve a sample or purchase supplies. However, in this later case, to reduce the use of clean gowning, we suggest the users contact Tim Goldhawk and ask him to place the samples/suppplies in the entrance of the nanofab
Staff Time - service work and equipment training:
- Faculty of Science accounts: $60/hr.
- non-FOS academic accounts: $90/hr
- Industrial training and instrument operation: $180/hr
- Industrial consulting and process development: $300/hr.
1540XB SEM/EDX and FIB
- $60/hr SEM/EDX equipment charge
- $40/hr FIB surcharge in addition to SEM charges ($100/hr)
1530 SEM and E-beam Lithography - $50/hr equipment charge
SEM Introductory Training
- $150 (includes 3 hour introductory session plus one hour of hands-on practice).
Spectroscopic Ellipsometer
-$25/hr, $25 minimum charge
Tencor P7 profilometer
--$50/hr, $100 minimum charge
MA6 Mask Aligner
-$50/hr, $25 minimum charge
Reactive Ion Etch and oxygen plasma - Trion - $50/hour
Plasma Enhanced Chemical Vapour Deposition (PECVD) - $5 per plasma minute
Metal Deposition (Standard metals)
-Osmium Coater -$10 per run
-E-beam evaporation - $50 per run (<1000 Ǻ metal ) plus $5 per 250 Ǻ (>1000 Ǻ metal )
-Surcharge for gold based on weight used and current cost per gram.
-Sputter Deposition - $25 per hour, $50 minimum
Film Spin Coating and Developing - $20 per substrate, includes cost of standard resists and developer
Dicing Saw - $50 for first hour, $25 each additional hour, $50 minimum
The entrance fee is waived when access involves only SEM imaging. In addition there is no entrance fee when entering the nanofab to retrieve a sample or purchase supplies. However, in this later case, to reduce the use of clean gowning, we suggest the users contact Tim Goldhawk and ask him to place the samples/suppplies in the entrance of the nanofab
Staff Time - service work and equipment training:
- Faculty of Science accounts: $60/hr.
- non-FOS academic accounts: $90/hr
- Industrial training and instrument operation: $180/hr
- Industrial consulting and process development: $300/hr.
1540XB SEM/EDX and FIB
- $60/hr SEM/EDX equipment charge
- $40/hr FIB surcharge in addition to SEM charges ($100/hr)
1530 SEM and E-beam Lithography - $50/hr equipment charge
SEM Introductory Training
- $150 (includes 3 hour introductory session plus one hour of hands-on practice).
Spectroscopic Ellipsometer
-$25/hr, $25 minimum charge
Tencor P7 profilometer
--$50/hr, $100 minimum charge
MA6 Mask Aligner
-$50/hr, $25 minimum charge
Reactive Ion Etch and oxygen plasma - Trion - $50/hour
Plasma Enhanced Chemical Vapour Deposition (PECVD) - $5 per plasma minute
Metal Deposition (Standard metals)
-Osmium Coater -$10 per run
-E-beam evaporation - $50 per run (<1000 Ǻ metal ) plus $5 per 250 Ǻ (>1000 Ǻ metal )
-Surcharge for gold based on weight used and current cost per gram.
-Sputter Deposition - $25 per hour, $50 minimum
Film Spin Coating and Developing - $20 per substrate, includes cost of standard resists and developer
Dicing Saw - $50 for first hour, $25 each additional hour, $50 minimum